Bluff Creek

This page serves homeowners who know their part of San Angelo as Bluff Creek. We could not confirm the exact boundaries of a neighborhood by that name, so rather than guess at local landmarks, this page focuses on something every San Angelo homeowner eventually faces: planning and comparing an HVAC replacement.

Planning a Replacement Before It Fails

Replacing a system in a rush, in the middle of July, rarely leads to the best decision. If your equipment is older, has needed several repairs or uses R-22 refrigerant, start planning now.

  • Gather information. Write down the model and serial numbers of the outdoor and indoor units, the filter size and any service history.
  • Note comfort problems. Rooms that run hot or cold, dust, noise and high bills should be part of the conversation.
  • Get more than one quote. Two or three quotes give you a sense of the range and the options.

Comparing Quotes Fairly

Make sure each quote covers the same items:

  • Equipment model numbers for indoor and outdoor units.
  • SEER2 and, for heat pumps, HSPF2 ratings.
  • A load calculation, not just a copy of the old size.
  • Line set, pad, disconnect, thermostat and haul-away.
  • Duct inspection and sealing.
  • Parts and labor warranty terms and who registers the equipment.

Common Questions

What is the minimum efficiency for a new AC in Texas?

For split systems installed since 2023, at least 14.3 SEER2 under 45,000 Btu/h and 13.8 SEER2 for larger systems.

Is the lowest price the best deal?

Not always. A lower quote may leave out items like duct sealing or a new line set. Compare scope as well as price.

How long does a replacement take?

Most straightforward replacements take a day. Duct or electrical work can add time.

Understanding the Numbers on a Quote

  • Tonnage. The cooling capacity. One ton equals 12,000 Btu per hour. Bigger is not better if it is oversized.
  • SEER2. Seasonal cooling efficiency. Higher numbers use less electricity over a season.
  • HSPF2. Heating efficiency for heat pumps.
  • AFUE. Heating efficiency for gas furnaces.
  • Stages. Single-stage systems run at one speed. Two-stage and variable-speed systems can run at lower speeds for steadier comfort.

Financing and Rebates

Some contractors and manufacturers offer financing, and some utilities or retail electric providers offer rebates for efficient equipment. Ask what is available, read the terms carefully and compare the total cost, not just the monthly payment.

Should I wait for my system to fail?

If it is old and repairs are adding up, replacing it on your schedule usually means better choices and less stress.

What questions should I ask an installer?

Ask how they sized the system, what is included, how long the work takes, what the warranties cover and whether they handle permits.

After Installation

Keep your invoice, model and serial numbers and warranty registration together. Schedule the first maintenance visit within a year. Ask the installer to show you how the thermostat works and where the filter goes. A well-installed system with regular maintenance gives you the best return on your investment. See cooling services for maintenance tips.

Repair First, Replace Later?

Sometimes a repair buys valuable time. A failed capacitor, contactor or fan motor on an otherwise healthy system is usually worth fixing, even if replacement is on the horizon. The decision gets harder with major failures: a compressor, a leaking coil or a cracked heat exchanger. In those cases, ask the technician for the repair price and a replacement estimate side by side, along with how much life the repaired system might reasonably have left. If the repair costs a large share of a new system, replacement often makes more sense. Either way, you should get the information you need to decide without pressure.

Getting Ready for Installation Day

Once you choose an installer, a little preparation makes the day go smoothly. Clear a path from the driveway to the outdoor unit and from the door to the attic or closet. Move cars so the crew can park close. Put pets in a safe room. Ask how long the system will be off and plan for heat or cold accordingly. After the work, walk through the new system with the installer, confirm the thermostat settings and ask for the paperwork, including model and serial numbers, warranty registration and any permit documents. Run the system for a day and call the installer if anything seems off, such as weak airflow, a new noise or water near the indoor unit. Most installers want to fix small issues right away rather than have them grow, and keeping notes from that first week helps if you need warranty service later.

Our Services

Replacement Quotes

Clear, itemized options for new systems. See AC installation.

Heating Replacement

Furnace, heat pump and dual-fuel options. See heating installation.

Why Homeowners Call Us

  • Itemized quotes that are easy to compare.
  • Sizing based on your home.
  • Prices before work begins.
  • Repair options if replacement can wait. See cooling services.

Contact Us

Share your system’s model numbers and age if you have them.

Tell us what you want to improve.